This concentrated, non-foaming liquid algaecide is designed to prevent and eliminate pool algae. It also clarifies water through flocculation and is compatible with most sanitization treatments.

The tablets disinfect pool water by eliminating harmful microorganisms, help prevent algae formation, and clarify the water by removing particles that cause turbidity.

The kit contains 0.5 kg of CTX-200/GR ClorShock 55% granular dichlorine and 0.5 l of CTX-500/S concentrated algaecide. It is intended for small inflatable or dismountable swimming pools.

Always dose the product with the filtration system running. Dilute the required quantity in a container with clean water, distribute it evenly over the entire pool surface, and keep the pump active during application.

For an initial treatment, use 2 liters per 100 m³ of pool water. For maintenance, use 1.5 liters per 100 m³ once per week. For water hardness above 35 °F and temperatures over 28°C, increase the dosage by 25 to 50 percent.

Dilute the required amount of CTX-700 in a container with water, then distribute the diluted solution evenly over the entire pool surface while the filtration system is running.

For pools with water hardness greater than 45°F and a temperature of 28°C, increase the dosage by 25 to 50%. If the water contains small amounts of iron, add CTX-700 before chlorination or another oxidizing treatment.

The water's pH should be maintained between 7.2 and 7.6, with daily monitoring using a proper pH analyzer or test kit.

It is designed to remove grease and dirt stains from pool edges, walls, the waterline, corners, and surrounding areas. It can also be used on PVC pool cover sheets.

Apply SGRASSANTE directly without diluting it, using a sponge to vigorously scrub the areas being treated.

For persistent dirt at the water level, lower the water level to enhance the product’s effectiveness.

This is a liquid winterizer for preserving water in unused outdoor and indoor pools during the winter months. It prevents algae proliferation, is non-foaming, fully water-soluble, copper-free, and compatible with all types of treatments, including P.H.M.B.

The Fidji round pool is available in four sizes: Ø 300 cm, Ø 350 cm, Ø 460 cm, and Ø 550 cm. All models have a height of 120 cm.

Yes. The swimming pools are sold as kits with a filtration system.

Yes. The GRE Haiti pool is sold as a complete kit with a filtration system included for operation.

No. It is installed above ground on a prepared flat and compacted surface, without excavation.

The board is delivered without anchoring hardware and must be correctly installed with proper anchoring and an appropriate pool depth.

Available lengths range from 1.4 m to 2.5 m, with sky blue and white color options.

The Balestra diving board is available in two lengths: 1.4 m and 1.8 m. Both variants are 0.25 m high and 0.4 m wide.

It is made from polyester resin reinforced with fibreglass, has an isophthalic gelcoat finish, and features a wide platform with an anti-slip coating.

The board is available in lengths of 2 m or 2.3 m, with a maximum load of 120 kg.

The board includes installation hardware, including anchors, board support, ring washers, and M14x60 bolts. Installation instructions are also included.

It is made from polyester resin and fibreglass and finished with a flexible, UV-resistant gel coat. The surface has anti-slip coverage, with adhesive grip strips in the spring area.

The diving board is supplied with an anchor compatible with Dolphin anchor model 00076.

Yes. A Sena pump appropriate to the model size is pre-mounted on the unit.

Use silica sand or glass media with a grain size of 0.4–0.8 mm.

The filter traps micro-particles during filtration. When the pressure rises 0.5 bar above the baseline, turn the lever manually or automatically to spin the cartridge and flush out debris through a tangential water flow.

Yes, it is compatible with most filtration systems using a standard 2-inch valve. The AstralPool valve, code 07444, is sold separately.

No. The selector valve must be ordered separately.

Use 0.4–0.8 mm quartz sand or compatible glass media.

Yes. The Aster filters are compatible with glass media as well as sand.

No. The side-mount 6-way valve must be purchased separately.

No. The multiport valve is not included and must be purchased separately as a compatible side-mounted valve.

The filter is compatible with certified sand measuring 0.4–0.8 mm or glass media. Its filtration bed is 1 meter deep.

The selector valve is included with Top-mounted models only. Side-mounted models are supplied without a valve, which must be purchased separately.

Yes. The Cantabric filter is compatible with both sand and glass filtration media.

No. The multiport valve is not included and must be purchased separately.

Yes. The filter is fully compatible with glass media instead of sand.

Yes. It is compatible with both glass and sand media, including monolayer and multilayer configurations.

It allows direct visual inspection and maintenance without dismantling the top diffuser, helping reduce downtime.

The filter is compatible with silica sand and glass filtration media, using the specified grain sizes.

Yes. The Artic Plus is designed for high-flow and continuous-operation environments, making it suitable for commercial pools.

Yes. It is compatible with both sand and glass filtration media when the media is correctly graded.

No. The filter is supplied without a side-mounted multiport selector valve, which must be selected and installed separately according to the connection size and hydraulic configuration.

Yes. The filter is compatible with both silica sand and glass filtration media.

Yes. Both sand and glass filtration media are compatible with these filters.

The EUROPE Pro Long version has a filtration bed that is about 25 percent higher. This added depth improves dirt retention, extends filtration cycles, and reduces wash frequency.

All models have standard 63 mm filter body ports and include 63 to 50 mm union tailpieces, so they are compatible with both 63 mm and 50 mm plumbing without additional reducers or fittings.

The filtration fineness is 15 to 20 microns.

No. Ozone disinfection is optional, and standard filtration and heating remain functional without it.

Only if the spa model and hydraulic layout match the listed compatibility. Verification before purchase is essential.

The valve provides six functions: filtration, backwash, rinse, recirculation, emptying, and closed.

Always stop the pump before moving the selector handle or changing position. Do not run the pump when the valve is in the closed position.

The KEOPS is complete and pre-assembled with an Aster filter, a Sena pump, a valve battery, an electric panel, and a chlorine and bromine dispenser. The dispenser is not included; an optional dispenser for 4 kg off-line chlorine and bromine tablets is available on request.

The KEOPS measures 1.20 m wide, 1.38 m long, and 1.14 m high, and weighs 110 kg.

The Hydrospin is a hydrocyclonic pre-filter for swimming pool filtration systems. It can be fitted to both new and existing installations and is mounted between the pump and the filter. It separates solids down to 40 microns.

Choose the version that matches your existing transformer or power supply. Available voltage options are 12 V AC and 24 V DC, depending on the reference.

No. The spotlight operates exclusively through On Off switching and does not require a remote control.

Yes. The projector must be installed fully underwater, and a compatible niche is required but sold separately. Verify that the niche diameter is between 180 and 190 mm before purchase.

Yes, it is suitable for salt water pools up to 6 g per liter of NaCl.

The rechargeable battery provides 8 to 20 hours of autonomy, depending on the brightness and lighting mode. The average charging time is 6 hours.

No. For the best lifespan, remove the lamp after use. Do not leave it permanently submerged, and do not charge it near water.

Yes. It is optimized for spas and compact pools, and can also be used in prefabricated or small residential pools where space is limited.

The PROHEAT II is designed to operate from 0 ºC upwards. For lower temperatures, consider models with inverter technology.

Yes. Its titanium heat exchanger is corrosion-resistant and compatible with saltwater pools.

Yes. It is designed for year-round use and can operate at ambient temperatures as low as -12 °C.

Yes. Its reversible cycle supports both heating and cooling, allowing it to cool the pool during hot seasons.

Yes. It works with salt systems up to 6 g per litre.

Yes. Its vertical airflow allows the unit to fit closer to walls and structures, reducing installation constraints by up to 70 percent compared with front-discharge units.

Position the unit next to your pool’s filtration system and connect it with 32/38 mm or 50 mm hoses. Ensure a minimum water flow of 2 m³/h, set the desired temperature on the digital control panel, and allow the pump to maintain the temperature automatically.

Choose the model based on your pool volume: BP-50 NR is for pools up to 30 m³, BP-85 NR up to 40 m³, BP-100 NR up to 50 m³, BP-120 NR up to 60 m³, and BP-140 NR up to 80 m³.

No. Wi-Fi is optional for smart control and is not required for the heat pump to operate.

It is compatible with pools up to 50 m³.

You can set the desired water temperature using the LCD display or WiFi app.

The unit automatically adjusts its power output to maintain the selected temperature.

Depending on sun exposure and pool size, the LUX 800 can increase pool water temperature by up to 6°C.

Yes. The AISI 316 stainless steel is designed to resist salt and high chlorine exposure.

The ladder is available in 2-, 3-, 4-, or 5-step configurations. The 3-step model is intended for pools around 1 metre deep, the 4-step model for pools around 1.2 to 1.3 metres, and the 5-step model for deep pools exceeding 1.5 metres.

The safety step is the first step at the top of the ladder and is twice as wide as the other steps, providing a larger landing area when entering or exiting the pool.

The ladder supports a maximum load of 150 kg. It is available with either 2 steps plus 1 safety step or 3 steps plus 1 safety step.

Rinse the ladder weekly with fresh tap water to help prevent dry salt or chemical deposits.

Avoid shock treatments or manual dosing near the ladder, and never use steel wool or carbon steel brushes. If small rust spots appear, use a non-abrasive metal cleaner and wipe in the direction of the polished grain.

The ladder is available in 2-step, 3-step, 4-step, and 5-step Luxe models, with product references 05480, 05481, 05482, and 05483 respectively.

The ladder is available with 1, 2, 3, or 4 Luxe steps, each combined with 1 Double Safety Step. These options are intended for shallow access points, pools approximately 1 metre deep, pools around 1.25 metres deep, and pool walls up to 1.5 metres deep, respectively.

Rinse the area where the ladder meets the water line weekly with fresh tap water, and avoid abrasive cleaners or steel wool. For small deposits, use a non-abrasive metal cleaner or a very diluted nitric acid solution, then rinse thoroughly.

Yes. The AISI 316L stainless steel is designed for high-chloride environments. Correct grounding and regular rinsing are recommended to help resist corrosion.

You need a set of standard spanners to secure the steps and anchors. The earthing cable must be connected to the anchoring fixtures.

Yes. The AISI 316 stainless steel offers higher corrosion resistance in salt-treated water when properly maintained.

The available options support minimum pool depths from 740 mm to 1520 mm. Model 08090 is for a minimum depth of 740 mm, 08091 for 1000 mm, 08092 for 1260 mm, and 08093 for 1520 mm.

Choose 05540 for an 800 x 800 mm pair embedded in concrete during construction, or 05541 for the same wide format with flange fixing on a finished deck.

Choose 05542 for the compact 470 x 800 mm format with a standard fixing plate, or 05543 for the same compact format with rectangular flange geometry.

Yes. The fixing versions are supplied with gaskets, screws, and wall plugs.

They are suitable for saltwater pools provided water chemistry remains controlled and the rails are cleaned regularly to prevent salt deposits and surface contamination.

Embedded models are installed directly into the pool deck during construction, while flange models are fixed to finished surfaces using plates, gaskets, plugs, and screws.

The series includes embedded models 00034 and 00035, available in lengths of 1220 mm and 1524 mm. Flange-mounted models 00036 and 00037 are also available in those lengths and include gaskets, plugs, and screws.

Model 07780 uses embedded anchors installed within the pool deck structure. Model 07781 uses external base plates for surface installation and includes screws and gaskets.

The handle is made from polished AISI 316L stainless steel and has a 43 mm tube diameter, 800 mm height, and 1250 mm length. It is supplied as a single grab rail.

It is designed for pool ladders with Ø 43 mm stainless steel handrails and a tube thickness of 1.2 mm. It does not fit ladders with different handrail diameters, thicker structural tubes, or non-standard ladder constructions.

The ladder has handrails made from Ø43mm hand-polished stainless steel tube and stainless steel, non-slip steps. Its design is intended to avoid slipping or cutting yourself, and it includes fixing plugs and an earth connection.

The dimensions are A 1840 mm, B 1220 mm, and C 1260 mm. Its maximum sustainable load is 150 kg.

It is designed for therapeutic pools and as an alternative to a ladder, helping disabled people or people with reduced mobility get in and out of the pool.

The lift has a polished AISI 316 stainless steel structure, measures 650 mm × 517 mm × 765 mm, and supports a maximum load of 115 kg.

Operation requires a mains water intake with a minimum pressure of 3. 5 kg/cm2.

The ladder is made of AISI-316 stainless steel and plastic, with a shiny, polished finish.

The dimensions are A 2100 mm, B 1480 mm, and C 1520 mm. The maximum sustainable load is 150 kg.

It is a step kit for adapting a stairway from 500 mm to 970 mm. One Step Kit is required for each rung of the stair. The kit is made with polished AISI-316 stainless steel and a plastic step with a non-slip surface.

For a 970 mm ladder with seven steps, order one 00119 and seven 28615 kits.

It is a shower tunnel for public swimming pools with one arch and three shower heads. It is made of polished AISI-304 stainless steel with a Ø 28 mm tube, and has a width of 1.2 m and a maximum height of 2.5 m.

The shower tunnel is supplied with an anchor plug and screws. Its packing size is 220 x 20 x 25 cm, and it weighs 10 kg.

No. It heats water using solar radiation stored in the internal tank.

Install it on a flat, stable surface using the integrated anchor, and connect it to the water supply according to local plumbing standards.

For the solar version, place it in an area with direct sunlight exposure. Rinse the shower head periodically to limit limescale buildup.

No. It reduces limescale buildup, but periodic cleaning is still necessary.

The available options are the Niagara Standard with a manual valve and anti-limescale diffuser, the Niagara Touchless with proximity sensor operation, and the Niagara Solar with an integrated 30-litre solar tank.

The shower is available in a solar version with an integrated 30-litre tank or a standard hot and cold version without a solar tank. Both versions include two front nebulizer jets.

The shower is made from tropical wood and satin stainless steel AISI 316. It has a mixer and single-lever valve for controlling cold and hot water.

The shower is 217 cm high, and the shower head is 204 cm from the ground. It has a rainfall system, an adjustable spray head, and an anti-limescale sprayer.

Yes. The timed push button controls the water duration, so the water stops automatically after the defined time.

Available options include models with one, two, or four overhead shower heads. A model with one overhead shower head and an integrated foot wash is also available.

Yes. The removable anchorage and locking system allow the shower to be dismounted without breaking the concrete base.

No. It is designed for specific shower pipe diameters, so verify the column diameter before purchase. The available options are for Ø 43 mm or Ø 63 mm shower columns, depending on the model.

The tray measures 100 cm x 80 cm, has a shallow profile, and weighs 9 kg.

The molded anti-slip relief provides grip when the surface is wet.

Soft integrated slopes guide water toward the drain, helping limit stagnation and splash back.

No. The outlet is adjustable, allowing alignment with the existing drainage layout.

No, this product includes only the shower tray.

Yes. The structure and surface are intended for high-traffic public areas when installed correctly.

Standard cleaning and periodic inspection of the drainage are sufficient.

Install it on a flat, stable base near the pool entrance. Connect the inlet nozzle to the water supply, ensure the overflow outlet drains correctly, and verify the water level before allowing users to access the area.

Installation requires the dedicated anchoring plate, which is sold separately, along with a correctly sized hydraulic line. Pump capacity and hydraulic balance should be verified before installation.

On a clear, sunny day, the water typically reaches a comfortable temperature in 2 to 3 hours. Peak temperatures are usually achieved by midday.

These showers are designed for seasonal use. To prevent damage from freezing water expanding inside the tank, they must be drained and stored or protected during winter months.

No. This is a non-solar model and delivers water at the temperature of your main supply. For hot water, it must be connected to a pre-mixed warm-water line, or you can consider the Chrome Solar version.

Yes. The foot washer is a dedicated tap at the lower part of the column, so you can wash your feet independently without getting your hair or clothes wet.

The shower uses a 30-liter internal tank as a solar collector, absorbing heat from the sun to provide warm water without electrical wiring or increased utility bills. For best results, place it in an unshaded, south-facing location with at least 6 hours of direct sunlight.

Before the first frost, empty the tank completely using the drainage valve to prevent freezing water from expanding inside the stainless steel tube. Periodically wipe the metallic framework with a soft cloth, and avoid abrasive chemical cleaners on the colored framework.

It is an open anchor for securing a swimming pool ladder on the edge of the pool.

The anchor is made of plastic. Its dimensions are A: 98 mm, B: 80 mm, and width: 65 mm.

It allows the automatic opening and closing of the water circuit through a timed photocell and a solenoid valve.

The control column is made of AISI-304 stainless steel and is 85 cm high. It includes a transformer with 220 V input and 24 V output, a timed photocell, a solenoid valve, anchor plugs and screws. Its packaging dimensions are 90 x 15 x 15 cm, and it weighs 8 kg.

Yes. All models are suitable for salt electrolysis systems and can be used with chlorinated and salt electrolysis pools.

Yes. The pump includes PVC connectors for 50 mm and 63 mm pipe systems.

Yes. The pump’s water-contact parts are made from AISI-316 stainless steel and are described as compatible with salt chlorination.

Yes. The pump is self-priming up to 2 metres without a check valve.

Yes. The VS AUT model can be controlled from a phone when connected to iQPUMP and the iAquaLink™ app.

Yes. It is compatible with salt water up to 6 g/L salinity (6000 ppm).

Yes. Its “Easy Retrofit” compatibility allows it to replace most existing pumps without modifying the piping.

Yes. It is compatible with saltwater pools up to 6 g/l (6,000 ppm) salinity.

It can be used for emptying and refilling pool tanks, recirculating and dosing treatments during water analysis, emergency water removal or drainage, and professional pool service and technical interventions.

The unit includes a FLOPRO 100M 1. 00 HP single-phase pump, a ZODIAC CS 100 cartridge filter, a bronze check valve, a differential switch, and 25 m of flame-resistant electric cable.

Combinations for filtering groups and valves are available on request.

It is compatible with Zodiac FloPro VS and FloPro VS AUT pumps. It is not compatible with single-speed pumps or non-Zodiac pump models.

Yes. Configuration is possible using WiFi direct mode between your phone and the device, even without internet access.

Rinse the electrode with distilled water, immerse it in the pH 4 buffer solution, wait for the reading to stabilize, and adjust the meter as instructed by the manufacturer.

For two- or three-point calibration, repeat the process using pH 7 or pH 9 buffers.

No. Use fresh solution for each calibration to ensure accuracy. The solution does expire, so check the expiration date printed on the bottle for guaranteed stability.

The Hydroxinator® iQ is designed for pools from 40 to 160 m³, with variants offering chlorine output from 10 to 35 g/h.

Yes. When paired with the optional pH Link or Dual Link modules, the system can automatically regulate pH and chlorine using ORP control.

EiSalt 12 is designed for pools up to 50 m³, EiSalt 21 for pools up to 90 m³, and EiSalt 30 for pools up to 140 m³.

Install the system after the filter in the hydraulic circuit. Add salt directly to the pool at 5 kg/m³, then wait 24 hours with circulation running before activating the system.

Select the desired chlorine output using the LED interface. The system generates chlorine automatically while filtration is active. For pools with automatic covers, output is reduced to 10%.

Very little maintenance is needed because automatic polarity inversion helps keep the cell clean.

Install the control box in a ventilated technical room at least 2 m from the pool edge.

Connect the compact cell horizontally to the return plumbing after filtration, then set the desired output level through the LED interface. For Ei² Expert, configure the timer, season modes, and pool cover automation.

The AstralPool Energy Sel is a saltwater electrolysis system for private pools. It automatically generates chlorine from salt dissolved in the water, eliminating the need for traditional chlorine tablets. It is available in three models: Energy Sel 30, 55, and 95.

The recommended salt level is 4.0 g/L, with a minimum of 3.5 g/L. When installing the system, the source recommends adding 400 kg of salt per 100 m³ of water.

Model 54051 is for pools up to 30 m³, model 54052 is for pools up to 55 m³, and model 54053 is for pools up to 95 m³.

First, power off the chlorinator and isolate the power supply. Remove the existing electrode from the cell housing, then insert the new electrode with a tight, watertight fit.

Restart the system and check the control panel for normal chlorine production.

No, installation is not included. The necessary anchors and water inlets are provided, and a pool technician or qualified installer is recommended.

No. The slide is designed for continuous water flow to ensure safety and usability, and using it dry is not recommended.

Yes. The AquaJet 50 supports above-ground installation using the optional telescopic support leg.

Model 11372 has a 1000-liter capacity and measures 162 × 122 × 83 cm. Model 17144 also has a 1000-liter capacity and measures 158 × 92 × 95 cm. Model 27865 has a 2000-liter capacity and measures 204 × 160 × 75 cm.

Install the tank below the overflow channel discharge line and connect it to the filtration suction circuit. Automatic level control sensors should be installed inside the tank, with inspection access provided for cleaning and maintenance. The sensors are typically installed separately as part of the hydraulic control system.

The spa accommodates five people with three seats and two reclining loungers.

This is a high-value custom supply spa rather than a standard shelf item, so the order must match the agreed configuration, finish, and technical requirements.

Customers are strongly advised to contact the supplier before purchase to confirm the design, option combination, installation context, and supply specification before production and dispatch.

The spa has four ergonomic seats designed for seated hydromassage relaxation.

The spa combines cartridge filtration with ultraviolet sanitation to help maintain clean water while reducing chemical use.

It accommodates five people with three seats and two loungers. Its dimensions are 233 x 233 x 91 cm.

Because the spa is produced and supplied on demand, contact LordsWorld before purchase to confirm the selected configuration, installation context, delivery access, and electrical compatibility.

It is designed for 5 users, with 3 seated positions and 2 loungers.

This spa is made to order and sold in exact commercial configurations. The correct reference, finish, and equipment package must be confirmed before production starts.

The Pacific 70 accommodates six people with five seats and one lounger. It includes 51 stainless steel hydrotherapy jets, 10 air injectors, two waterfalls, three headrests, and a 1,138-litre water capacity.

The spa is suitable for outdoor terraces, gardens, and indoor wellness rooms. It can be supplied with a cabinet or without one for recessed installations, and it requires a stable base capable of supporting its full filled weight. It is compatible with a 230 V residential electrical supply.

Yes. It is designed primarily for couples, with two full loungers and one additional seat.

The spa has three seating positions in total: one seat and two loungers.

Yes. Electrical connection and site preparation should be handled by qualified installers.

The spa also requires professional electrical and hydraulic installation.

Yes. It requires an appropriate electrical supply of 230 V or 400 V and professional installation because of its weight and hydraulic connections.

Yes. Because this is a high-value custom supply spa, you should contact the supplier before purchase to confirm the design, options, installation context, and supply specification.

The Creta Swimspa measures 400 x 230 x 138 cm and has a water capacity of 6000 litres.

Yes. Five turbo jets create an adjustable counter-current flow for continuous swimming in a compact water space.

Because the swimspa is manufactured and supplied on demand, contact the team before ordering to confirm the cabinet finish, insulation level, and optional equipment before production and delivery.

It has six positions: five seats and one lounger. The spa measures 216 × 216 × 90 cm and has a 930-litre water capacity.

Because the spa is manufactured and supplied on demand, contact the team before ordering to confirm the cabinet finish, insulation level, and optional equipment. The final configuration should also be checked against the installation requirements and site conditions.

The spa accommodates five people with three ergonomic seats and two full loungers. Its massage system includes 32 stainless steel water jets and 12 air injectors.

Contact the team before ordering so the cabinet finish, insulation level, and installation conditions can be confirmed before production and delivery. The spa is produced on demand by AstralPool.

No. It is designed for recessed or lined residential installation and requires a proper filtration system, hydraulic installation, and compatible electrical supply. It is not designed for portable above-ground installation.

The spa has six seating positions, consisting of five seats and one lounger. Its dimensions are 216 x 216 x 90 cm, with a water capacity of 980 L and 28 hydrotherapy jets.

No. An external filtration kit is required: reference 41993CE000 or 41993CE001.

The circular seating arrangement accommodates five seated users.

The spa is designed for installation in a reinforced concrete structure with an overflow edge perimeter. It requires external filtration equipment, a surge tank, and professional hydraulic and electrical installation; it is not designed as a standalone portable hot tub or for above-ground installation.

No. The surge tank is a separate installation component required for overflow spas. The spa shell includes the hydromassage components, while filtration and hydraulic systems must be installed externally according to the project design.

No. The spa requires a dedicated external filtration system and surge tank, typically installed in the wellness facility’s technical room.

The spa has nine seated positions arranged around its circular basin.

No. The spa connects to an external filtration system in the plant room, and a surge tank is required for overflow installations but purchased separately.

The spa accommodates five users simultaneously, with three seated positions and two reclined loungers.

The AstralPool Olympia measures 365 x 280 cm, has a 2,490-litre water capacity, and provides 12 seats, 16 hydromassage jets, and 16 air injectors.

The spa is manufactured and supplied on demand. Buyers should contact the team before ordering to confirm the exact configuration, lighting option, and accessories before production and delivery.

The spa is designed for in-ground installation with overflow-edge hydraulic circulation and is compatible with commercial filtration systems and compact filtration kits 50 or 75.

It requires an external surge tank and filtration equipment for operation. Heating can be provided by a water-to-water heat exchanger or an electric heating system.

The product is manufactured and supplied on demand. Contact the team before ordering to confirm the exact cabinet finish, insulation level, and optional equipment before production and delivery.

The spa accommodates five bathers simultaneously, with three sitting positions and two loungers.

Contact the team before ordering so the exact cabinet finish, insulation level, and optional equipment can be confirmed before production and delivery.

Install the ALASKA unit on a level surface outdoors. Connect it in bypass after the filtration system and before any chemical dosing. Set the desired outlet temperature using the control panel, and make sure the water circulation pump is running before switching on the unit.

Yes. The titanium heat exchanger is fully resistant to salt and corrosion.

No. SIBERIA chillers are designed exclusively for indoor installation in a well-ventilated technical room with ducts for air intake and exhaust.

Yes. The SIBERIA range is compatible with saltwater and chemically treated pools, using corrosion-resistant titanium heat exchangers.

The range includes the Pool Bottom Brush (Model 36615), Wall Brush (Model 36616), and Pool Corner Suction Brush (Model 36617).

The brushes are made from gray shark polypropylene, with white and blue polypropylene bristles. Their construction is UV-resistant and robust.

The SHARK SERIES includes a surface net for collecting leaves along the waterline and a bottom net with an integrated bag for collecting dirt and leaves from the pool’s bottom.

The nets are made from high-quality gray shark polypropylene, with a polyester net welded to the collector body. They are resistant to UV rays and chlorine.

The net has a white polypropylene support, white polyester mesh, and aluminum.

Two variants are listed: 23360-RETINO is the surface model, and 23361-RETINO is the bottom model.

It gradually dissolves slow-dissolving Trichlor or Bromine tablets into the pool’s circulation line. In-line models use the Venturi effect, while off-line models use a bypass with integrated valves. The dosing rate can be adjusted with control knobs.

The feeder is designed only for trichlor or bromine tablets.

It operates without electricity, using either the Venturi effect or a bypass connection. Models are available for both in-line and off-line installation.

Yes. It is designed for integration with dosing systems used in pool and water treatment applications.

Yes. The semi-transparent body and integrated scale allow direct visual level checks without opening the tank.

They are compatible with the Zodiac eXO® iQ and eXO® iQ LS salt chlorinator systems.

No. Installation must be performed by qualified technicians to maintain the warranty and ensure safety. The probes should also be calibrated before use with the specified buffer solutions.

It is a floating chemical dispenser for private and above-ground pools. Its lower regulator lets you determine the amount of chlorine entering the circulation, and its flotation signaling system helps you check how much chlorine remains.

The dispenser can contain up to 1 kg of tablets.

It is used to dose a liquid sanitizer.

It has an externally adjustable dosage scale and includes a 50 mesh suction filter, equivalent to 250 μm. Its piston acts on the dispenser to maintain proportionality between the circulation flow and the absorbed product.

It has a capacity of 5 tablets weighing 200 grams each.

The dispenser is gray shark and measures 0.183 m high, 0.226 m long, and 0.225 m wide.

Before adding the media, half-fill the filter with water to cushion the glass during installation. Distribute the glass evenly across the filter bed and leave approximately 30% free space for expansion during backwash cycles.

Perform an initial rinse to remove fine particles, followed by a longer rinse cycle. Avoid inhaling dust and wear gloves and a mask during handling and installation.

The available granulometries are 0.5–1.0 mm, 1.0–3.0 mm, and 3.0–7.0 mm. The 0.5–1.0 mm and 1.0–3.0 mm options are also listed in 10 kg bucket variants, as is the 3.0–7.0 mm option.

It is designed for swimming pool sand filters and is compatible with above-ground and in-ground pools. It can also be used for plant drainage, aquarium environments, and construction projects.

Zodiac Crystal Clear is made from 100% pure, crushed glass crystals and filters particles down to 20 microns for clear pool water. It can reduce water usage by up to 75% compared with traditional sand filters and lasts three times longer than sand.

The floating pipes are available in lengths of 10 m, 15 m, and 30 m, with diameters of 38 mm (1½”) and 50 mm (2”).

Secure all connections to prevent leaks and avoid sharp bends to maintain optimal flow.

Regularly inspect the pipes for wear and tear, and store unused pipes in a cool, dry place to help prevent damage.

It is specifically designed to clean concrete pools effectively.

It is compatible with 1½” and 2” terminal sizes.

Its articulated design provides flexible movement for reaching corners and crevices, while heavy-duty wheels support smooth navigation across pool surfaces. The joint mechanism adapts to different pool shapes and sizes.

Inspect it regularly for wear or damage, clean it thoroughly after each use to prevent buildup, and store it in a dry place to help avoid material degradation.

It is compatible with hose diameters of 32 mm and 38 mm. It connects to a telescopic pole using fork or wing nut fixing.

It is designed to efficiently remove fine particles and sand from the bottom of your pool.

The underwater cylindrical thermometer (Item Code: 20593) provides discreet temperature readings, while the cylindrical floating thermometer (Item Code: 20594) stays visible on the water’s surface for quick checks.

Check the temperature regularly and ensure the thermometer is securely placed underwater or floating to avoid inaccuracies.

Rinse it with fresh water after each use to prevent buildup and maintain clarity.

When not in use, store it in a dry place and avoid exposing it to harsh chemicals or extreme temperatures beyond its operating range.

The thermometer has a float at the top that allows accurate measurement of pool water temperature. Readings can be taken without removing it from the water.

It measures water temperature in both degrees Celsius and degrees Fahrenheit.

It monitors water temperature, pH, disinfectant concentration (Redox/ORP), and water conductivity in real time. The BLUE by RiiOT app lets you monitor your pool remotely.

No. Each listed item is sold separately, and you will receive the exact variant selected at purchase.

The kit measures total chlorine, bromine, and pH in pool and spa water using liquid OTO and Phenol Red reagents. Results are interpreted through visual color comparison with the included color scale.

Perform the OTO test before the pH test, because high chlorine levels can affect the accuracy of the pH reading. Rinse the cuvettes thoroughly with the same pool water before testing to help avoid contamination and inaccurate results.

Store the reagents in a cool, dry place away from sunlight. Wear protective gloves and glasses, keep the components out of children’s reach, and use the reagents in a well-ventilated area.

Remove the cap and rinse the chambers with sample water. Fill both chambers with fresh sample water taken from approximately 30 cm below the surface.

Add the appropriate reagent tablets without touching them directly. Wait for them to dissolve fully, then immediately compare the colours with the chart. Rinse and dry the kit after each use to prevent contamination.

Available variants include chlorine with pH, oxygen with pH, bromine with pH, iron, and hydrogen peroxide with pH. The chlorine ranges are 0.1–3.0 mg/l or 0.5–6.0 mg/l; oxygen is 0–10 mg/l; bromine is 1.0–8.0 mg/l; iron is 0–8.0 mg/l or 1–10 mg/l; and hydrogen peroxide is 5–50 mg/l. The pH range for the pH variants is 6.8–8.2.

These tablets are specifically formulated for use with Pooltester, Checkit, and Pool Check devices. They are not intended for use with other test kits.

The MINIKIT AF 422 tests cyanuric acid from 20–200 mg/L, the MINIKIT 14627 measures total alkalinity from 20–800 mg/L CaCO₃, and the MINIKIT 14629 measures calcium hardness from 10–500 mg/L CaCO₃.

Rinse the compartments and containers with the pool water sample before each test. Use the appropriate tablet reagent without touching it with your fingers, wait for the tablet to dissolve completely, and compare the color immediately for an accurate reading.

After the analysis, rinse the containers thoroughly, using a brush if needed, to help avoid contamination during future tests.

Dip one strip into the pool water to a depth of 5 cm and hold it for 2 seconds. Remove it, shake off excess water, wait 15 seconds for the colors to develop, and compare each pad with the color chart on the bottle.

The kit includes a white plastic comparison case, liquid Hardness 1 and Hardness 2 reagents, and a reading chart. The kit code is 70522.

Collect a water sample in the test vial, then add the correct amount of Hardness 1 reagent followed by Hardness 2.

Shake gently, compare the resulting color with the reference card, note the calcium hardness level, and take appropriate action if necessary.

Depending on the configuration, the photometers test chlorine, pH, cyanuric acid, total alkalinity, calcium hardness, and bromine. They are available in 3-in-1, 5-in-1, and 6-in-1 versions.

No. Reagents must be purchased separately based on your test requirements.

The PM 600 covers 13 parameters, while the MultiDirect offers up to 98 measurement methods.

The tablets are compatible with Scuba II, MD100, MD200, PM600, MultiDirect, and XD Series photometers. They use 24 mm cuvettes.

The range supports testing for free and total chlorine, pH, cyanuric acid, calcium hardness, alkalinity, ozone, phosphates, and metals including iron, copper, and aluminium.

The Crystallic is optimized for smaller pools and focuses on floor cleaning, with a 1.5-hour cleaning cycle and 59 µm filtration.

The Imperial is designed for larger pools and cleans the floor, walls, and waterline. It has a 2-hour cleaning cycle, dual motors, and active brush technology.

Ensure the cleaner is fully submerged before starting the cleaning cycle, clean the filter baskets regularly, and store it in a cool, dry location when not in use.

Disconnect the device from power before maintenance, keep it out of reach of children and pets during operation, and do not use it in pools with chemical imbalances or excessive debris.

The RT 2100 cleans the pool floor only, while the RT 3200 cleans both the floor and walls. The RT 2100 is designed for pools up to 8 x 4 m, and the RT 3200 for pools up to 10 x 5 m.

Lift the top lid and rinse the filter basket under running water. The source also recommends cleaning the filter after each use to maintain suction efficiency.

No. It is an electric robotic cleaner that works independently from the pool filtration system.

RA 6700 iQ and RA 6800 iQ are suitable for pools up to 15 x 7 m. RA 6900 iQ is suitable for pools up to 20 x 10 m.

The RE4400 iQ is the core connected configuration with remote On and Off control. The RE4600 iQ adds advanced remote functionality, adjustable cleaning time, a Lift System and a transport trolley.

No. The Voyager operates independently with its own suction system and removable filter, so connection to the pool filtration system is not required.

Connect the suction robot directly to the pool’s suction socket or skimmer; no electrical connection is needed.

Use a hose length equal to the greatest distance the robot can travel from the connection point to the farthest corner of the pool, plus 1 metre. For optimal installation, test the cleaner and adjust its suction with a control valve.

It is suitable for inground pools and rigid-wall above-ground pools, with a recommended maximum pool size of 12 × 6 metres. It can be used in rectangular, oval, and free-shape pools with flat, slightly sloped, or compound-sloped bottoms.

It is designed for small volumes, spas, and small swimming pools. No electrical connection is required.

The package includes a steel filter, two cleaning nozzles, and a wall support.

The hose should be the greatest distance the robot can travel inside the pool, measured from the connection point to the farthest corner, plus 1 metre.

The suction robot connects directly to the pool’s suction socket or skimmer, and no electrical connection is needed.

Choose a hose length equal to the greatest distance the robot can travel from the connection point to the far corner of the pool, plus 1 metre. For optimal installation, test the robot and adjust its suction using a control valve.

It is suitable for inground pools and rigid-wall above-ground pools up to a recommended maximum size of 12 × 6 metres. It can be used in rectangular, oval and free-form pools.

The supported pool bottoms include flat, slightly sloped, compound-sloped and hopper-type designs. Supported linings include tiles, liner, polyester, reinforced PVC and painted concrete. The robot cleans the bottom and walls.

They can typically be reused for 6 to 10 cycles, depending on pressure and contamination.

GARNET can be used to clean and prepare surfaces made of steel, stainless steel, non-ferrous metals, wood, glass, marble, and building facades.

Corundum is available in 25 kg bags, 5 kg buckets, and 1000 kg pallets.

ASILIKOS can be used for sandblasting steel, metals, concrete, reinforced concrete, wood, and glass. It cleans surfaces, removes rust, and creates opaque finishes.

Available grain sizes range from 0.2–0.5 mm to 1.4–2.8 mm. The abrasive is supplied in 25 kg paper bags on EURO pallets, with 1,000 kg / 1,350 kg big bags and bulk packaging available on request.

POLEN is suitable for steel, metals, concrete, and other materials. It can be used for cleaning, rust removal, and surface preparation before painting.

Each machine is packaged with its included components, such as abrasive tubes, non-toxic tubes where applicable, nozzles, sieves, ventilation or aeration kits, and protective gear such as aerated helmets or masks.

The recommended operating pressure is 1.5 to 8 bar. Air consumption is 600 lt/min with a Ø6 nozzle and 800 lt/min with a Ø8 nozzle.

Select the correct size, inspect the gloves for wear or damage before each use, and clean them with mild detergent before air drying.

Store them in a cool, dry place away from direct sunlight, and replace them if damage or excessive wear is detected.

The nozzles are available in tungsten carbide or boron carbide, with diameters of 6 mm, 8 mm, and 10 mm.

Regularly inspect the nozzles for signs of wear and replace them as needed. Clean them after each use to prevent abrasive buildup and prolong their lifespan.

The nozzles are made of tungsten carbide, have a length of 70 mm, and are available in diameters from 3 mm to 10 mm. They include flanged fixation.

The available variants support nozzle diameters of 20 mm, 25 mm, 30 mm, 40 mm, and 48 mm.

It is available for D40 and D48 tubes and accommodates various nozzle sizes.

Clean the nozzle and holder threads before installation, use the D40 or D48 variant that matches your tube, and avoid over-tightening to prevent thread damage.

Regularly inspect the holder for wear and replace it if necessary.

It separates and removes atmospheric humidity from the air system to help prevent damage to operating equipment.

The M03 helmet includes an aerated floppy hood, a semi-mask with adjustable rubber, a round glass lens, a corrugated pipe, a filter, a silencer, and a flow regulator.

The source states that helmets and hoods are important for sanders, especially for blasting operations outside blasting cabins, where surface abrasion can disperse dust and abrasive blasting material into the environment.

The gun is made of aluminum for lightness of movement. It includes an air injector and brass nozzle stop ring, plus a rubber holder for the abrasive tube in hardened steel.

The working pressure is 3–10 ATM, and the maximum pressure is 12 bar.

The SA1 uses a direct, tool-free connection to vacuum sandblasting systems. It has a 0.11 m connection diameter.

The SA1 is compatible with vacuum sandblasting cabinets and suction-type blasting systems. It works with dry media such as glass microspheres, abrasive sand, garnet, and metallic grit.

It is not suitable for pressure blasting systems without dust extraction, wet blasting or slurry-based systems, or toxic dust without certified filtration compliance.

The lithium-ion battery provides more than 8 hours of autonomy and takes 3 hours to recharge.

P3 filters protect against solid and liquid aerosols such as dust, fumes, and mist. A2P3 filters also include activated carbon protection against organic vapors, including those found in many pesticides and solvents.

The system is not suitable for environments with oxygen levels below 17 percent, compressed air supply lines, or protection against carbon monoxide.

Choose the P3 model for solid or liquid particles only.

For solvents, pesticides, fuels, or mixed chemical exposure, select A1P3, A2P3, A2B2P3, or ABE2K1P3 according to the risk assessment.

They are compatible with respirators and powered air-purifying systems using EN 148 1 threaded connectors, including full face masks and PAPR units that accept a standard 40 mm thread.

They are not compatible with bayonet connection systems and are not suitable for oxygen-deficient atmospheres below 17 percent oxygen.

Lava Stone is suitable for gas BBQs, saunas, and aquarium decoration. It is available in 5 kg, 10 kg, and 15 kg packages, with stones approximately 25–75 mm in size.

Clean the stones thoroughly before first use. For aquarium use, rinse them thoroughly with water. Do not use chemical cleaners or detergents, as the stones may absorb them and become unsafe for BBQ and aquarium use.

The log holder measures 70 × 44 cm and weighs 7 kg.

The log holder measures 70 × 45 cm, weighs 12.5 kg, and is made of 3 mm thick steel.

The Turyn log holder has a modern, universal design and is made from sturdy black steel. Its elements are welded together to create a stable product, and it can be placed next to a fire pit for convenient wood storage.

The Atos firewood holder is made of powder-coated steel profiles. Its elements are welded rather than screwed, creating a robust construction.

The holder measures 120 x 40 x 20 cm and weighs 5 kg.

The rack measures 150 × 50 × 20 cm and weighs 5 kg.

It is made of powder-coated steel profiles. Its elements are welded rather than screwed, making the rack robust and weather resistant.

The firewood rack measures 120 x 40 x 20 cm, weighs 4 kg, is painted, and is made of steel.

It is designed to store firewood in one easily accessible place and is suitable for use near a living room fireplace. Its powder-coated steel profiles make it weather resistant.

The rack measures 120 × 40 × 20 cm and weighs 4 kg.

It is made from powder-coated steel profiles and has welded elements rather than screwed ones.

The holder is made with powder-coated steel profiles. Its elements are welded rather than screwed, making the rack robust and weather resistant, with a stated service life of around ten years.

The dimensions are 60 × 90 × 25 cm, and the product weighs 7 kg.

The holder has a diameter of 80 cm and a height of 82 cm. It is made from welded steel profiles with a powder-coated finish and weighs approximately 4 kg.

Place the rack on a flat indoor surface near your fireplace or stove, then load firewood vertically following the spiral shape.

Stack the logs evenly for balance and visual consistency. No assembly or fixing is required.

The firewood holder measures 80 × 85 × 20 cm and weighs 4 kg.

It is made of powder-coated steel profiles, which make it weather resistant.

The firewood holder’s listed dimensions are 80 × 85 × 20 cm. It weighs 4 kg, is painted, and is made of steel.

It is made with powder-coated steel profiles and is described as weather resistant.

Its elements are welded rather than screwed, making the rack robust and giving it a stated service life of around ten years.

The wood holder measures 90 x 60 x 25 cm and weighs 5 kg. It is made of steel and is painted.

It is made with powder-coated steel profiles, making it weather resistant.

Its elements are welded rather than screwed, making the rack robust and giving it a service life of around ten years. It is handmade in Europe.

The wood holder measures 90 × 60 × 25 cm and weighs 8 kg.

It is made of powder-coated steel profiles and has welded elements rather than screwed ones. The construction is described as weather resistant and robust, with a service life of around ten years.

The fire screen measures 95 × 76 × 20 cm and weighs 5 kg. It is made from powder-coated steel profiles and steel mesh.

The fire screen measures 100 × 72 × 20 cm and weighs 4 kg. It is made from powder-coated steel profiles and steel mesh.

The fire screen measures 100 × 72 × 20 cm, weighs 5 kg, and is made from steel profiles and steel mesh. It is painted.

Yes. It is described as a decorative fireplace cover and can also be used as a radiator cover. Its powder-coated steel profiles make it weather resistant.

The fire screen measures 100 × 72 × 20 cm and weighs 5 kg.

It is made from steel profiles and steel mesh, with a powder-coated finish.

The fire bowl has a 60 cm diameter, 20 cm total height, and 68 cm total width. It weighs 8 kg and is made from natural steel with a 2 mm thickness.

It can be used as a place to build a fire, a portable grill, a source of heat, and stylish lighting. Handles welded on both sides make it easy to move from one place to another.

The brazier is made of steel and measures 60 cm in diameter, 17 cm high, and 68 cm wide. It weighs 8 kg and has a steel thickness of 2 mm.

The brazier has a diameter of 60 cm, a height of 36 cm, and a width of 68 cm. It weighs 10 kg and is made of steel.

It can be used as a place to build a fire, a portable grill, a source of heat, or stylish lighting.

The welded side handles make it easy to move from one place to another, while the bowl shape helps prevent burning wood from spreading in strong winds.

The brazier has a 60 cm diameter, is 39 cm high and 75 cm wide. It is made of 2 mm thick steel and weighs 11 kg.

It can serve as a place to build a fire, a portable grill, a source of heat and stylish lighting.

Handles welded on both sides allow it to be moved from one place to another.

The brazier is made of steel, with a 60 cm diameter, 30 cm height, 68 cm width, and 2 mm thickness. It weighs 10 kg.

The brazier has a diameter and width of 60 cm, a height of 36 cm, and is made of steel. Its steel thickness is 2 mm and it weighs 13 kg.

It can be used as a place to build a fire, a portable grill, a source of heat, or stylish lighting. Handles welded on both sides make it easy to move from one place to another.

The brazier has a diameter and width of 60 cm, a height of 36 cm, and is made of 2 mm thick steel. It weighs 11 kg.

The brazier has a diameter and width of 60 cm, a height of 32 cm, and is made of 2 mm thick steel. It weighs 9 kg.

It can be used to build a fire, as a portable grill, as a source of heat, and for stylish lighting. Handles welded on both sides make it easy to move.

The brazier has a diameter and width of 60 cm, a height of 29 cm, and is made of steel. Its listed weight is 13.5 kg and its steel thickness is 2 mm.

It can be used as a place to build a fire, a portable grill, a source of heat, and stylish lighting.

Handles welded on both sides make it easy to move from one place to another.

The brazier has a 60 cm diameter, is 30 cm high, and 68 cm wide. It is made of steel with a 2 mm thickness and weighs 11 kg.

The MONTANA fire bowl is made of thick steel, with all elements welded together for a stable and solid structure. It includes storage space for firewood and handles on both sides for easier movement.

The fire bowl has a 60 cm diameter, is 45 cm high and 68 cm wide. Its steel is 2 mm thick, and the product weighs 18 kg.

It can be used as a place to build a fire, a portable grill, a source of heat, and stylish lighting. Its bowl shape helps prevent burning wood from spreading in strong winds, and the welded handles make it easy to move.

The fire bowl has a diameter of 60 cm, a height of 80 cm, a width of 68 cm, and weighs 22 kg. It is made of steel and has a material thickness of 2 mm.

The portable fire pit can be used as a place to build a fire, a portable grill, a source of heat, and stylish lighting. Its bowl shape helps prevent burning wood from spreading, including in strong winds.

The brazier is 30 cm high and 70 cm wide. It is made of steel, has a 2 mm thickness, and weighs 17 kg.

It is a handmade product made of thick steel in Europe.

It can be used to build a fire, as a portable grill, as a source of heat, or for stylish lighting. Handles welded on both sides make it easy to move from one place to another.

The brazier is made of steel and measures 70 cm wide by 35 cm high. Its steel bowl is 2 mm thick.

The portable fire pit can be used to build a fire, as a portable grill, as a source of heat, or as stylish lighting. Its bowl shape helps prevent burning wood from spreading, and the welded handles on both sides make it easy to move.

The portable fire pit can be used as a place to build a fire, a portable grill, a source of heat, and stylish lighting. Its bowl shape helps prevent burning wood from spreading, for example in strong winds. Handles welded on both sides make it easy to move from one place to another.

It can be used as a place to build a fire, a portable grill, a source of heat, and stylish lighting. Handles welded on both sides make it easy to move from one place to another, while the bowl shape helps prevent burning wood from spreading in strong winds.

Let the grill cool, remove the detachable parts, empty the fat tray, and clean the non-stick surface with a soft sponge.

Use the 5-level thermostat. Start with a lower level for delicate foods and raise it for searing and faster browning.

It runs for up to 5.5 hours on full tanks.

No. It is designed for use without a chimney and is a free-standing indoor fireplace.

Assemble the mantle using the supplied panels, then insert the steel unit from the front. Fill the burner within its limit and ignite it with a long lighter. Refill only when the burner is cold.

No, a flue is not required. However, the niche must be insulated because the wall can heat up.

The fireplace has a thermal power of 4.11 kW and is designed to heat rooms up to 26 m².

Its 3.5-liter burner provides a burning duration of up to 5 hours 30 minutes and uses bioethanol fuel.

No. It requires no flue, no electricity, and no fixed installation.

Place it on a flat, non-flammable surface, remove the burner, and fill it carefully with bioethanol. Wipe up any spilled fuel immediately, then ignite it with a long lighter and allow the flame to stabilize before normal use.

Use only bioethanol fuel, never refill it while hot or burning, keep a minimum 1 meter safety distance, operate it only in ventilated environments, and do not leave it unattended during operation.

No. It is intended for decorative and occasional use, not continuous heating.

Use bioethanol fuel intended for fireplaces, following the fuel label instructions.

Use the included flame snuffer to stop the flame, then wait for the fireplace to cool fully before moving or refilling it.

No. It operates without a chimney, flue, or electrical connection.

Yes. It can be installed on a solid, non-flammable wall using the supplied wall mounting kit or placed on a stable horizontal surface.

The fireplace runs exclusively on bioethanol. It is freestanding and requires no chimney, electrical connection, or structural modification.

Place it on a solid, non-flammable floor. Fill the burner only when it is cool, then ignite it with a long lighter while keeping a safe distance.

Allow 10 to 15 minutes for the flame to stabilize fully. Extinguish it with the supplied burner cover and never use water.

Yes, it is suitable for indoor use when operated in a ventilated environment and according to the safety instructions.

No installation or fixing is required, and the fireplace does not need an electrical connection.

No. It is fully electric and requires no chimney, gas, or flue installation.

Yes. The decorative flame effect operates independently, so you can use it without turning on the heat.

No. It operates fully electrically and does not require a chimney.

Yes. The flame effect and heating operate independently, so you can use the flame-only mode without increasing the temperature.

Yes. The flame effect operates independently from the heating function and consumes 40 W.

No. The fireplace arrives fully assembled and is ready to use without installation work.

Yes. The flame effect operates independently from the heating function, so you can use it for ambience without heat.

No. The unit is delivered pre assembled and does not require structural installation.

Yes. The flame effect works independently from the heating function, so you can use flame-only mode for visual ambiance without increasing the temperature.

No. It is a freestanding fireplace that is ready to use without fixed installation. Place it on a flat indoor surface and connect it to a standard 220–240 V electrical outlet.

No. It operates without a flue or exhaust system.

One fill lasts up to 8 hours and 30 minutes, depending on the flame setting.

Under correct ventilation, it can heat spaces up to 70 m³ or approximately 28 m².

No. It operates exclusively on liquid bioethanol and does not require a chimney, gas connection, or electrical connection.

Place it on a flat, heat-resistant surface, fill the burner with approved bioethanol, and light it with a long lighter. Let the flame stabilize before adjusting room ventilation, and extinguish it only after the fuel cycle completes or using the supplied method.

No. The structure arrives fully assembled.

It is designed for single rooms up to 25 square meters.

No. The fireplace requires no chimney or flue and is delivered fully assembled. Place it on a stable, level surface.

Use only certified bioethanol fuel, place the fireplace on a stable, level surface, and ignite it according to the supplied burner instructions. Allow the flame to stabilize before leaving it unattended.

Never refill while the burner is hot. Operate the fireplace only in well-ventilated rooms, and do not move it while it is operating.

No installation is required. One refill lasts approximately 3 hours of continuous operation.

One fill lasts up to 4 hours, depending on the flame setting and room conditions.

The manufacturer’s guidance targets rooms up to 26 m².

One 2.7 L fill lasts up to 8 hours, depending on operating conditions.

The fireplace burns for up to 8 hours per fill, depending on operating conditions, and has a heat output of 1.5 kW.

The panel is designed for small indoor spaces measuring 4 to 8 m² and has an expected warm-up time of around 5 minutes. Actual results depend on insulation, ceiling height, and outside temperature.

Mount the panel securely using anchors rated for the wall material and product weight, and keep free space around it. The panel reaches 70 °C, so keep children and pets away from direct contact. Do not cover it, keep it away from splashes and high-humidity zones, and disconnect power before cleaning or moving it.

The stated heated area is 4 to 8 m². Actual coverage can vary with insulation, ceiling height, and drafts.

Mount the panel on a stable wall surface and place it where people spend time, away from curtains or furniture. Keep clearance around it, do not cover the front surface, keep it away from water and humid splash zones, and disconnect power before cleaning after it has cooled down.

Braciere Venere is a two-piece outdoor brazier made of carbon steel with a rust-effect finish. It includes a base and a brazier tray, designed to hold the fire at a comfortable height while adding a rustic garden atmosphere.

Place it outdoors on a flat, stable, non-flammable surface with clear space around it. Use suitable firewood or charcoal and safe ignition methods.

Let the brazier cool fully before moving, cleaning, or covering it. Keep it away from buildings, furniture, dry grass, and low branches, and do not leave it unattended during operation.

It offers two power settings: 500 W and 1000 W.

The LEO 12702 is a freestanding heating panel designed for floor placement.

Yes. It carries an IP55 water resistance rating. Place it in a safe outdoor position and follow electrical safety rules for outdoor sockets and extensions.

Place the table on a flat, stable surface and connect it to a suitable electrical outlet matching 220 to 240 V and 50 to 60 Hz. Switch it on to start heating at the fixed 1500 W level.

After use, switch it off and unplug it. Wait for it to cool fully before moving or storing it, and store it in a dry place when not in use for long periods.

No. They are decorative ceramic logs intended for decorative use only and are non-combustible.

Place the logs around the burner according to your fireplace layout. Do not block the burner openings or fuel flow.

Use them only with bioethanol fireplaces, and position them when the fireplace is cold.

The 0.5-liter burner has a fuel consumption of 0.22 liters per hour and burns for up to 2 hours per refill.

No. MONET operates without a flue, gas connection, or electrical power, so no chimney or permanent installation is required.

Yes. It can be used freestanding on a stable, flat surface or mounted on the wall using the included fixing kit.

No. It is designed to operate without a chimney, flue, or gas connection.

Use only certified bioethanol fuel. Store it in sealed containers away from heat, and never refill the burner while it is hot.

No. The bioethanol stove does not require a flue or chimney, so no structural work is needed for installation.

One refill lasts up to 6 hours, depending on the flame setting.

No. The stove works independently without a power connection.

Approximately 5 hours, depending on the flame adjustment.